Lorem ipsum dolor

Thermo-Shield Roof coat

Thermoshield Roof Coat is made from a proprietary formula that can increase a structure’s efficiency and lead to significant energy savings. 

645,00$

Call For Price

Thermoshield Roof Coat is made from a proprietary formula that can increase a structure’s efficiency and lead to significant energy savings. The flexible coatings are made from a water-based compound of pure acrylic resin filled with vacuumed sodium borosilicate ceramic microspheres.

The tiny spheres - each approximately 100 microns in size - combine to create a smooth membrane that acts like a thermal blanket over the roof. Despite being very thin, this “blanket” can dramatically increase efficiency. Because the coating is seamless, it can easily bridge small cracks and gaps in the roofing structure.

The Thermoshield formula is completely non-toxic, so it is environmentally friendly. When dried, it is washable and able to repel most substances, including harsh chemicals. Thermoshield Roof Coats are highly reflective, so they do not absorb heat from the sun. Because the coats have a very low conductance value, they

  1. 1) keep cooler air under the roof from escaping and
  2. 2) do not conduct solar heat to the area under the roof. The roof coats also reduce noise transmission and protect the structure itself from UV rays. The roof coatings will be effective in almost all climates. They have an effective use range from -40 degrees C to 204 degrees C.
Thermoshield Roof Coat may be utilized wherever a weather-resistant membrane-like coating is required. The coating will adhere to many surfaces, including:
wood, foam, galvanized steel, aluminum, asphalt roof shingles, concrete, and asbestos.
  • Standard coating is ideal for most climates. 
  • Special tropical coating provides the same benefits as standard coating, but it also protects against fungus growth.
  • UL CLASS A formula coating is available for structures that require extra fire resistance (in the oil and gas industry, for example).
Statistics Reflectance 89%, Emittance 94%, Conductance 0.05 W/mK.

Typical under-roof insulation slows the transmission of heat and cold, but it does not stop heat loss or gain. This is where Thermoshield’s impressive reflectivity, emittance and conductance performance is important. The heat from the sun (solar gain) is only a problem if it is absorbed by the roof. Thermoshield reflects most of this heat back into the atmosphere, and its low conductance value means that any heat that remains does not pass through the roof. This will not only provide cooling shade to the structure that the roof covers, it will also lower cooling costs overall. The coatings will work in extreme environments. They will remain flexible down to -45.6 degrees C and maintain their integrity up to 204.44 degrees C.
The coatings provide excellent resistance to ponding water on a roof. This is because the membrane becomes water resistant when it is saturated. The polymers that make up the membrane swell when wet, closing the pores so that nothing passes through. As they dry, however, these pores open, allowing the water to evaporate easily. it also provide an excellent adhesion to a wide variety of substrates: wood, urethane foam, galvanized steel, aluminum, asphalt roof shingles, concrete, asbestos and many others.
  •  Primer is not required. However, rusty surfaces do require treatment prior to the application of Thermoshield. Furthermore, our proprietary Acrylic Flex Tac bonding coat is necessary before the Roof Coat itself can be applied to bitumen roofs.
  •  The surface should be cleaned prior to application. Power washing is recommended, provided it does not damage the roof.
  •  Drying time is 45 minutes for the first coat, 12 hours for a second boat and 12 hours to dry through. This is the ideal drying time for average conditions of 24 degrees C and 50% relative humidity.
  • Do not apply if precipitation is imminent.
  • Thinning is not required, though 0.24 litres (one cup) of water may be added to replace evaporation loss or to adjust consistency for paint sprayer.
  • Average coverage area: 3 m² per gallon at 700 microns DFT (32 sf/gallon at 27 Mills DFT) OR 7 m² per gallon at 380 microns DFT (75 sf/gallon at 12 Mills DFT)
  • 2-3 coats are required for maximum long term effectiveness.
  • Mixing : Stir each container thoroughly using low speed mechanical agitation to avoid air entrapment
  • Methods : To assure adequate and uniform coverage, the “spray and back roll” techniques are recommended. Thermoshield® Roof Coats should be applied in full wet coats.

Spreading rate per coat (1 millimeter = 1000 microns)
m²/gallon WFT(microns) DFT(microns) Suggested 9 371 (15 mills) 233 (10 mills)
Maximum 12 275 (11 mills) 175 (7 mills) Minimum 6 567 (23 mills) 350 (14 mills)
This rate allows for 10% loss
  •  Roller or airless paint sprayer recommended. Very small areas may be brushed. When applied by brush, three coats, cross-brushed, are required for adequate protection.
  •  Airless Sprayer details:
Tip Orifice 0.78mm (0.031 inches)
Atomizing Pressure 2200 - 2500 psi
Fan Spread 60 Degrees
Pump Minimum one gallon per minute at 2500 psi
Filter Remove filters and screens

  • Prime pump with water before attempting to spray Thermoshield® Roof Coats.
  •  Custom colors are available, but darker colors will have lower reflectivity values.
  •  Packaging options: 5 gallon pails or 55 gallon drums.
  •  Shipping weight:
Weight per gallon 4.5 kg (10 lbs)
Five gallon pails 22.7 kg (50 lbs)
55 gallon drums 272 kg (600 lbs)
  •  Store between 1 degree C and 30 degrees C. Coatings are not flammable, but do not allow to freeze.
  •   Shelf life: two years
  • V.O.C. : 39.5 grams / liter (0.33 lbs / gallon)
  • Product codes : STANDARD WHITE: 5962 / STANDARD ACCENT BASE: 5965 / TROPICAL WHITE: 5966 / TROPICAL ACCENT BASE: 5967 / UL CLASS A: 5975
This product comes with a five year warranty. This period is extendable to 10 or 15 years. The sole remedy for goods not in conformance with any warranty is replacement of the product. Thermoshield shall not be liable for any other damages, including, but not limited to, labor expenses.

Related Products

Thermoshield Wall Coats can be applied to both interior and exterior walls. When the flexible, water-based coating dries, it creates a seamless...

Thermoshield Wood & Deck Coat is a water-based sealant that provides both water resistance and protection from UV rays. 

Thermoshield Clear Coat seals and protects a variety of substrates. When applied correctly, it creates a strong acrylic ...

Thermoshield Wall Coats can be applied to both interior and exterior walls. When the flexible, water-based coating dries, it creates a seamless...

Thermoshield Roof Coat is made from a proprietary formula that can increase a structure’s efficiency and lead to significant energy savings. 

Thermoshield Metal Primer inhibits the spread of rust on metal structures. This corrosion resistant coating is made from 100% acrylic resin...

Thermoshield Tank Shield is a highly efficient, flexible coating that is designed to protect and lower the external surface temperature...

Thermoshield Stucco Shield can be applied in place of paint or as an alternative to multiple-layer stucco systems.

Thermoshield Stucco Shield can be applied in place of paint or as an alternative to multiple-layer stucco systems.

Thermoshield Acrylic Flex Tac is specifically designed to be used as a primer on bitumen surfaces